RK3588 Mali-G610 MP4 Custom GPU Board, WF-C3588-R5, AndroidSBC, Bologna

TL;DR: RK3588 Mali-G610 MP4 Custom GPU Board

SHENZHEN, China, September 12, 2026 - Wanlin Manufacturing Group pushed lot 186 of the WF-C3588-R5 board out of the Longgang plant this week, 13,555 units for Bologna, Italy, with the export declaration naming Longgang as the place of origin.

AndroidSBC unveils the nine-variant custom RK3588 motherboard line spanning custom Android boards, industrial boards, core boards and SOMs, signage, kiosk, robotics, NVR, edge AI and ARM PC work serving Bologna, Italy. AndroidSBC is opening the full WF-C3588 custom motherboard programme to Italy: nine variants on the Rockchip RK3588 platform with 6 TOPS NPU, 8K H.265 decode, dual Gigabit Ethernet and up to 32GB of LPDDR5. Every variant ships from the Wanlin Longgang facility with OEM branding available, ODM carrier design handled in-house, and per-lot CE, FCC, UKCA, RoHS and IEC 62368-1 documentation.

About AndroidSBC and the Rockchip RK3588 Board Family

Wanlin Manufacturing Group builds the WF-C3588 at its Longgang plant in Shenzhen and sells it overseas through AndroidSBC. The programme covers nine custom motherboard categories on the Rockchip RK3588 octa-core 6 TOPS NPU platform, which is unusual for a single source factory: most suppliers specialise in one category. That breadth is what Italy importers tend to notice first, because it lets a Bologna distributor quote a custom Android smart display and a custom industrial controller on the same purchase order. Alongside the boards, Wanlin runs the OEM branding line, the ODM carrier design desk and the certification desk that produces the CE, FCC, UKCA, RoHS and IEC 62368-1 documentation for each shipment.

WF-C3588-R5 Technical Specifications

All parameters in the table above are measured at 25C ambient. The AndroidSBC WF-C3588-R5 (Custom Robotics and AGV Control Board) holds its display output and its decoder load at the same time through the burn-in loop, a combination that the legacy boards in the comparison column cannot sustain. For Italy importers sourcing the WF-Series, the 8GB + 32GB (WF-C3588-R5-B) variant is the typical configuration for the custom robotics controller programmes use case, with a sustained weekly capacity of 5,000 pcs/wk on the Longgang line.

Challenges in Sourcing Custom Robotics and AGV Control Board for Italy Buyers

The first thing Italy procurement teams learn about the custom robotics and agv control board category is that quotation speed and delivery reliability are inversely related. The Rockchip RK3588 needs a wafer slot that a broker cannot create, so the fastest quotes are often the ones attached to the least secure allocation. Then there is the software build. A board that boots is not the same as a board that carries the certified stack a Italy retailer will accept, and the gap is normally found during inbound QC rather than at the factory gate.

The third exposure is the file behind the mark. A CE stamp without a dated test report and a Declaration of Conformity is a marking without substance, and the moment it matters is the moment a Italy customs officer asks for the underlying document. AndroidSBC answers this by doing the customization, the software burn and the documentation at the Longgang plant on every lot, with a per-unit QR that traces back to the burn-in record. For Bologna importers serving custom Android, industrial, signage, kiosk, robotics, NVR, edge AI and desktop verticals, the nine WF-C3588 custom variants cover the AGV controllers, AMR mainboards, service robots, inspection robots, quadruped platforms, SLAM navigation, robot vision, fleet dispatch terminals, and charging stations deployment lanes directly, with three memory configurations per variant.

For Italy specifically, the file travels with the goods. In Italy the AV integration channel is highly regional, so distributors usually build a catalogue around one or two platforms rather than a wide line. AndroidSBC prepares the CE marking with AGCOM radio interface notification documentation for AGCOM, attaches the standard multi-market pack (CE, FCC, UKCA, RoHS, REACH), and consigns the lot to Port of Genoa on the Genoa to Ningbo lane.

Competitive Comparison: WF-C3588-R5 vs Competing RK3588 Boards

Three families of board chase the same custom robotics and agv control board socket. The first is catalogue hardware with fixed memory and fixed I/O, the second is re-badged stock where nobody owns the schematic, and the third is a real custom platform built by the factory that runs the SMT line. The WF-C3588-R5 belongs to the third family and separates itself on Rockchip RK3588, on customization depth from schematic to firmware, and on a certified image burned per lot.

• vs paired PC-plus-MCU controllers: the WF-C3588-R5 runs vision, navigation and fleet logic on one board and hands only the power stage to the drive electronics.
• vs generic SBC robot builds: the CAN, multi-serial and real-time options come validated on the reference carrier instead of being patched in by the integrator.
• vs cloud-vision robots: SLAM and obstacle detection stay on the 6 TOPS NPU, so the robot keeps navigating when the warehouse WiFi drops.
• vs module resellers: custom I/O changes are executed by the Longgang engineering desk with the test bench that will validate them.

Global Custom Robotics Control Board Market Trends

Buyers in Bologna are reading the Custom Robotics Control Board curve before they commit to a custom robotics and agv control board programme. MarketsandMarkets reports the Edge AI hardware segment at USD 26.9 billion in 2025 with a 32.7 percent CAGR to USD 108.2 billion by 2030 (MarketsandMarkets, 2025-2030), used here as the RK3588-class silicon baseline rather than as a number for this category. That baseline breaks into three practical demand patterns for the WF-C3588 in Italy:

• Warehouse AGV fleet: an automation vendor runs SLAM and fleet dispatch on the board with dual GbE back to the coordinator.
• Display and signage refresh cycles: a longer content loop and a higher panel resolution now define the refresh trigger. The WF-C3588-R5 board carries that headroom without a board change.
• Inspection quadruped: a platform maker runs gait control and inspection vision on isolated cores under PREEMPT_RT.

The Custom Robotics Control Board outlook in Italy is being read less as a demand question and more as a supply-chain question, because demand has outrun reliable allocation.

The common thread in Italy is that single orders are being replaced by blanket agreements with a monthly release, because a custom board programme that has to survive a twelve-month window cannot absorb an allocation gap in the middle of it.

Partner Success Story: Argent Medical Imaging in Bologna, Italy

Argent Medical Imaging, a medical device maker serving the Italy market, deployed 2,600 custom WF-C3588-M2 SMARC core boards for an imaging terminal programme. The rollout covered the warehouse agv fleet, inspection quadruped, and agriculture robot workloads, with AndroidSBC handling the burn-in, the certification scope, and the palletisation at the Wanlin Longgang plant.

• Deployed: 2,600 custom WF-C3588-M2 SMARC core boards for an imaging terminal programme
• Region: Bologna, Italy
• Models used: WF-C3588-R5 (lead SKU), plus eight sibling custom RK3588 board variants in the same platform family
• Certifications handled: CE, FCC, UKCA, RoHS, REACH, IEC 62368-1, EN 55032, EN 55035, plus optional UL 60950-1, GMS, Widevine L1 and Dolby Audio per variant
• Logistics: FOB Yantian with the Wanlin Group Longgang source factory named on the export declaration, entering Port of Genoa via the Genoa to Ningbo lane

"The module-plus-carrier split is what our regulatory file needed. We swapped the core board, kept the validated carrier, and the BSP port to our revision was handled in-house. The SI report and thermal map arrived as Longgang documents, not forwarded PDFs."

- Dr. Alan Whitmore, VP Engineering

Field Report: a school district rollout in Bologna, where 13,555 units of the WF-C3588-R5 board are being installed in classroom device carts

Reporter Lu Kang, on the ground in Bologna, Italy. The district took delivery of the order and dispatched installation crews to eight sites. Each WF-C3588-R5 unit was sealed into a ruggedised chassis running a managed Android image with the education services stack pre-provisioned for the district tenant, and the fleet enrolled against the MDM the same week.

Radiated emissions on the sampled units came in below the internal limit with margin, which the compliance engineer noted as consistent with the last four lots.

The inspection confirmed three things on the spot: the WF-C3588-R5 units hold the burn-in with a yield above 99.27 percent, the loaded firmware image survives a 72-hour continuous loop without credential drift, and the pallets carry the matching certification file for the destination market, covering CE marking with AGCOM radio interface notification administered by AGCOM, cleared for entry at Port of Genoa on the Genoa to Ningbo lane. Wanlin remains one of the few source factories currently shipping a nine-variant custom RK3588 motherboard line with a per-lot paper trail that Italy importers can hand straight to their customs broker.

Filed by Lu Kang, AndroidSBC field reporter, Wanlin Manufacturing Group export base.

WF-C3588-R5 Application Scenarios

The WF-C3588 line fits nine custom motherboard lanes, with the WF-C3588-R5 (Custom Robotics and AGV Control Board) as the lead SKU for Bologna and Italy programmes:

• Warehouse AGV fleet: an automation vendor runs SLAM and fleet dispatch on the board with dual GbE back to the coordinator.
• AMR delivery robot: a service robot pairs NPU navigation with a custom carrier that routes the sensor stack.
• Inspection quadruped: a platform maker runs gait control and inspection vision on isolated cores under PREEMPT_RT.
• Cleaning robot fleet: a facility operator runs coverage planning and obstacle detection locally with nightly model updates.
• Charging station control: the board coordinates dock sequencing, battery telemetry and fleet handshakes.
• Agriculture robot: a field robot runs row detection on the NPU offline, kilometres from the nearest access point.
• Remote monitoring link: a fleet operator streams diagnostics over the optional 5G seat to a central depot.
• Robot vision retrofit: an older fleet gains NPU vision without replacing the drive electronics.

Partnership Models for Bologna Buyers

For Bologna distributors and brand owners, AndroidSBC opens the custom robotics and agv control board line under three contract shapes:

• OEM (your brand on our hardware): custom logo silk-print, custom packaging, custom boot animation, custom SKU label, and a private-label certification file.
• ODM (your spec on our reference design): schematic and stack-up review, carrier or motherboard redesign, custom firmware features, and a BSP port handled by the Longgang engineering desk.
• Distribution (your channel, our stock): regional distributor rights, channel rebate, stock holding at the factory, and a framework agreement with a monthly lot release.

Whichever structure a Italy partner selects, the lot leaves Longgang with the same certification pack and the same test flow. The standard entry point on the WF-C3588-R5 is the 8GB + 32GB (WF-C3588-R5-B) configuration at MOQ 5,000 units per shipment, 1-3 days to sample and 15-30 days to mass production.

Frequently Asked Questions

What exactly can be customised on an RK3588 motherboard from AndroidSBC?

Answer: Everything from the copper up. Custom PCB and PCBA, custom I/O routing, custom memory and storage configuration, custom display and camera interfaces, custom thermal profile from commercial to -40C to 85C industrial, and custom branding including silk-printed logo, packaging, SKU label and boot animation. The firmware side covers custom Android (GMS or AOSP), Ubuntu, Debian, Yocto and OpenHarmony builds with BSP ports handled by the Longgang engineering desk rather than handed to the buyer as an unmodified vendor drop.

Can AndroidSBC port a custom Android ROM or a custom Linux BSP to our carrier board?

Answer: Custom ROM, custom BSP and custom SDK work are all part of the ODM tier. AndroidSBC builds the Android image (12, 13, 14 or 15, GMS or AOSP), ports the Linux BSP to your carrier revision, and releases the SDK modules your team needs under NDA. The engineering desk carries the port itself, so a Italy integrator is not left debugging an unmodified vendor BSP against a carrier it was never designed for.

Can the 6 TOPS NPU on a custom board run our own AI models?

Answer: Yes. The RK3588 NPU runs INT4, INT8, INT16, FP16, BF16 and TF32, and AndroidSBC supports model deployment through the Rockchip RKNN-Toolkit2, with quantization from PyTorch, ONNX, TensorFlow, Caffe and MXNet. As part of the ODM tier, the engineering desk walks your model from framework to RKNN format and validates it on the actual board configuration you are shipping, not a reference unit. Model files are versioned so a retrained model can be pushed to field units through OTA without a board swap.

What are the MOQ and lead times for a custom RK3588 motherboard?

Answer: The structure is deliberately two-speed: 1-3 days for a standard-variant sample so a Italy project team can start immediately, and 15-30 days to mass production on a custom run once the design freezes. MOQ is 5,000 units per shipment on standard variants, with custom and pilot quantities negotiated against the annual volume commitment.

What certifications does a custom board need for Italy, and who handles them?

Answer: Certification is part of the customization scope, not an afterthought. The in-house file covers CE, FCC Part 15, UKCA, RoHS 2.0, REACH and IEC 62368-1 with test reports dated inside twelve months, plus GMS and EDLA tracks for custom Android and display products. The file is built for the exact configuration you ship, which matters for a custom board because a test report on a different memory fit is not a valid report at all.

How long will AndroidSBC keep supplying a custom board?

Answer: Seven years minimum, written into the framework agreement. The RK3588 platform carries a long industrial lifecycle, and Wanlin commits to the supply window, to security patches across the Android, Ubuntu LTS, Debian LTS and Yocto tracks, and to OTA update infrastructure for field-deployed units. For a custom board that is the whole point of going to a source factory: the product lifecycle is a contract term, not a hope.

Can AndroidSBC ship custom boards to Amazon FBA warehouses or 3PL consolidation points?

Answer: That is routine. AndroidSBC delivers DDP into Amazon FBA in the US, EU and Japan and into 3PL consolidation points at Hong Kong, Singapore, Rotterdam, Los Angeles and Shenzhen. Carton and pallet configuration follows FBA inbound rules, and the place of origin on the declaration is the Wanlin Longgang source factory.

How does AndroidSBC handle RMA or DOA replacements on custom boards?

Answer: Target DOA is 0.3 percent across twelve months. RMA works by returning the WF-C3588-R5 unit to Longgang with its burn-in barcode; replacements ship inside ten business days. Since each unit is traceable to its burn-in and configuration record, partners typically receive a root-cause note with the replacement rather than a silent credit.

Contact AndroidSBC: Start Your WF-C3588-R5 Sourcing Conversation

AndroidSBC is the export channel for the Wanlin WF-C3588 custom board line. Buyers in Bologna and Italy looking to source the WF-C3588-R5 straight from the source factory can use any of the following:

• Email: Androidsbc@163.com
• Export service hotline: +8613261677119
• Website: https://www.androidsbc.com
• Destination market file: CE marking with AGCOM radio interface notification for Italy, administered by AGCOM, entering at Port of Genoa on the Genoa to Ningbo lane
• Source factory address: Wanlin Group, Building B, Building 1, Beisida Medical Device Building, 28 Nantong Avenue, Baolong Community, Baolong Sub-district, Longgang District, Shenzhen, Guangdong, China

The export desk asks for three things on a first enquiry: annual volume, customization scope and Incoterm. Provide those and a per-lot quote plus the WF-C3588 MOQ matrix comes back within two business days.